magfla wrote:maffla wrote:magfla wrote:My system service light is on and continues to beep. It says to refer to manual but I can't find it.There is no code #. How long dies it take
Please can you advise?
How long does it take to get a reply?
Can anyone help with Clormatic error code?
Can anyone help with Clormatic III model CM 301
-
- I'm new here
- Posts: 2
- Joined: Sat 21 Nov, 2009 11:45
- My Pool: clormatic III model #CM 301
- Location: florida
Can anyone help with Clormatic III model CM 301
[/quote][/quote]magfla wrote:My system service light is on and continues to beep. It says to refer to manual but I can't find it.There is a code # 121
Please can you advise?
-
- I'm new here
- Posts: 2
- Joined: Sat 21 Nov, 2009 11:45
- My Pool: clormatic III model #CM 301
- Location: florida
Can anyone help with Clormatic III model CM 301
[/quotemagfla wrote:My system service light is on and continues to beep. It says to refer to manual but I can't find it.There is no code #. How long does it take to get a reply>
Please can you advise?
Error Codes and Test Switches
Stevescricket wrote:Contact Alphatech. They will help you with the test swithes on the Clormatic 3 to isolate the problem. error codes 186 and 172 were intended inhouse use only.
dear steve, whih Alphatec? there a bunch on the web
thanks
Can anyone help with Clormatic error code?
clormatic cm301 code 181, 172 found no power to cell (22-28 volts) ?
Can anyone help with Clormatic error code?
Punamytsike wrote:I have Clormatic CM III CM 601 and got an error code 186 that does not exists in my manual. I acid washed the cell, so it is clean. It also gives me error code 172 at the same time.
Any help is appreciated.
I am getting Service code 120..Can anyone tell me what the corrective action should be? Thanks in advance.
Can anyone help with Clormatic error code?
i have a chlormatic II 601
a new electrode from 2 month without problem
and sudently a code service with message 113
can anyone help me about this code
thanks
a new electrode from 2 month without problem
and sudently a code service with message 113
can anyone help me about this code
thanks
Can anyone help with Clormatic error code?
Does anyone know what the codes 170 and 193 mean on the chloramatic 601?
Can anyone help with Clormatic error code?
Error code 170 is a power error, usually one of the circuit boards or the transformer. I'm not sure what 193 is, but it sounds like your control box is going bad.
-CG
-CG
Can anyone help with Clormatic error code?
If anyone needs spare parts for Clormatic 3 601, my cell finally died after 12 years. Flow sensor works, but I cut the PVC at the sleeve connector. All the boards and cords are good. I'm not selling, it's free if you pick up in Sarasota area, or prepay postage expense to mail beyond this area.
-
- I'm new here
- Posts: 1
- Joined: Thu 01 Nov, 2012 19:17
- My Pool: 10,000 gallon
Inground - Location: Apopka
Can anyone help with Clormatic error code?
joem3064 wrote:If anyone needs spare parts for Clormatic 3 601, my cell finally died after 12 years. Flow sensor works, but I cut the PVC at the sleeve connector. All the boards and cords are good. I'm not selling, it's free if you pick up in Sarasota area, or prepay postage expense to mail beyond this area.
joem3064,
Any chance you still have that flow sensor? I would definatly like to take it off your hands if you do. Mine just petered out this week after 6 years. It's throwing the 172/186 codes and has yellowish splotches that don't come off with wiping around the 3 sensors. My cell seems to be fine still and I have a new one ready to go, just in case it does die soon. I really don't want to switch out the plumbing to the new 3 port system yet though since I think it is just the sensor at this point. Seeing as how you got 12 years out of your cell in the same area of Florida gives me hope!
If you still have it I could paypal you postage or mail you a check. I'm in Apopka(Orlando area) my zip is 32712. Let me know.
Thanks- Doug
Can anyone help with Clormatic error code?
Millerzone41 wrote:What did anyone find out about error code 172 and 186? I cleaned the sensor like the manual said and it didn't work. Did anyone find a solution? Did a new one fix it?
Replace the flow senso. About $192.00
Re: Can anyone help with Clormatic error code?
Hello,
I was wondering if any of you had a back printed circuit (psd001) for a clormatic (cm601), i could buy? My problem is that i live in France (1st point) and it seems i can't find one here (2nd point).
Thank you,
Guillaume
I was wondering if any of you had a back printed circuit (psd001) for a clormatic (cm601), i could buy? My problem is that i live in France (1st point) and it seems i can't find one here (2nd point).
Thank you,
Guillaume
Return to “Salt Water Chlorine Generators, Ozone, UV”
Who is online at the Pool Help Forum
Users browsing this forum: No registered users and 13 guests