Stains on the pool surfaces, pool equipment
or on the swimmers, or off-color swimming pool
water. Discolored but clear pool water.
Pool Enthusiast
Pool Enthusiast
Posts: 12
Joined: Sun 13 Apr, 2008 11:17


Postby tacoma5050 » Tue 20 May, 2008 11:13

I found this on-line informaton about CHELATORS & SEQUESTRANTS very helpful. (attached below)

My question is: For control of iron from a pool heater. Which type of control is better; CHELATORS or SEQUESTRANTS?

And what are what are some product name examples or ingredients for each.



The word CHELATE is derived from the Greek word for "claw". In pool and spa chemistry chelate means a chemical treatment to control or "coat" soluble metal ions and prevent their oxidation into unwanted colored precipitates. A chelator attaches to a metal ion like copper or iron and wraps around it like a claw.

There are many types of chelators available in the market. Among the most widely used is a group of organic acids called "amino polycarboxylic acids". These chemicals are usually formulated into liquids that quickly attach to copper or iron ions and deactivate them. Please note that chelators will not react with metals such as finely divided iron shavings and they react very slowly with metals that are already oxidized or precipitated.

Sequestrants differ from chelators in the way they "coat" or react with mineral ions. Sequestrants generally have a few active sites on each molecule allowing it to control two or more metal ions at a time. Because of this, sequestrants are often more powerful as stain removers and are often sold with specific stain removal directions.


Many chelators and sequestrants have metal ION PREFERENCES called "displacements". This means that certain metal ions will be coated before others. The usual preference is iron, then copper, then manganese, then calcium, then magnesium. There are chelators that favor calcium first.

The EFFECTIVENESS of chelators and sequestrants to coat undesired metal ions depends on the concentration of the ions to be chelated. For example, it is easier to control 1 ppm of copper and 1 ppm of iron in soft water (50 ppm of calcium) than in hard water (350 ppm of calcium). The presence of 350 ppm of calcium in water, for example, will occupy a large portion of the chelator intended to control the copper and iron. With this in mind it is advisable to chelate or sequester undesired metal ions before adding calcium to the water.

The AMOUNT of chelator or sequestrant needed depends on the type of metal ions present. For example, copper, iron, and manganese all require about the same amount of chelator whereas calcium requires 50% more chelator. Reactions to control metal ions occur within seconds in most cases.

Chelators and sequestrants are PH AND OXIDIZER sensitive. Very low pH, occurring in a "pocket" of water where acid has been added, can cause loss of chelation. Very high pH, again a "pocket" effect, can also cause chelation failure and precipitation of copper or iron. Because most chelators and sequestrants are organic molecules, they are subject to attack by high levels of oxidizers and "wear off' over time. This is the reason that most product labels state that continued additions may be necessary to control metals. With this in mind, it is obvious that shock treatments should not be performed directly after chelators or sequestrants have been added.

TEMPERATURE and TDS (Total Dissolved Solids) have slight effects on chelation. According to manufacturer studies, high temperature and high TDS increase the amount of chelator or sequestrant needed.


What if you did shock after adding sequestering agent?

Postby Lger » Sun 17 Aug, 2008 13:35

I added "mineral Magnet" due to some black staining on my step of pool I think caused by trichlor tabs in floater. I assumed metals were still present even though I had just drained and acid washed my pool a few weeks prior.
I don't think there should be metals anywhere, but the step still turned black.

Anyway, I put in the mineral magent, no reaction until one day later I added a jug of chlorine and the water turned white milky and sudsy looking on top.
Now, I am battling getting the water clear, new filter, clarifyer etc. nothing seems to work. So since I shocked after adding the sequestering agent, what happened and how do I fix this?


Postby Guest » Sun 10 Jun, 2012 09:09

Keep cleaning the filter at least twice a day till the water becomes clear.
Swimming Pool Wizard
Swimming Pool Wizard
Posts: 72
Joined: Wed 20 Jul, 2016 05:45


Postby paulbest » Sun 07 Aug, 2016 19:37

all chelators are sequestrants but not all sequestrants are chelators, You know what I mean? chelating compounds have a ring structure whereas sequesterant might or might not have one, but they both have the same function and that is to "deactivate" a metal ion so it does not react with other substances in the water.

for swimming pools, the most commonly use are sequestrants. Sequestrant products are added to pool water to hold minerals and metals in solution and prevent staining of the pool shell. the very popular brand is from JACK'S MAGIC SAPHIRE, and EMERAL STUFF.

Return to “Pool Surface Staining & Discolored Pool Water”

Who is online at the Pool Help Forum

Users browsing this forum: No registered users and 0 guests